Skip to content

HOW-TO

How To Fix A Bogged Weed Eater-- Carburetor Replacement

by HIPA Jeremy 22 Sep 2022 0 Comments


Sting trimmer bogging has been a common problem. Now here is a step-by-step instruction on how to fix a bogged trimmer permanently by replacing the carburetor.

If you have your trimmer bogs when you go to throttle up and you have tried to adjust the screws on carburetor, you need to replace the carb.

How To

Before you start, if you have any old gas left in the fuel tank, you need to dump it out and refill with fresh fuel.
Step 1: You want to remove the air filter cover, the air filter, and the air filter housing with an eight-millimeter nut driver.
Step 2: In case there is pressure in the fuel line, you need to loosen the fuel cap. If you do not do that, there is pressure when you remove the fuel line and the fuel cap is just going to squirt gas.
Step 3: Take the carburetor off. Now you need to remove the gasket and the fuel lines that are connected to the carburetor. You should be careful when you do this because it is very easy to damage the fuel line. But the throttle cable is still connected, push it down and it is going to disconnect itself from the carburetor. Here, you can get the entire carburetor removed.
Step 4: Reinstall the new carb. Do not forget to reconnect the throttle cable and the fuel lines to the new carburetor.
Step 5: Put the air filter housing, air filter and the cover back on.
Step 6: What is left to do is start the engine up to check if the carburetor needs any adjustments.

Carburetor adjustments

The High-Speed Screw

You need to start with the high-speed screw rather than the low-speed screw on a string trimmer. However, low-speed adjustment is the top priority on chainsaws.
1.Press and hold the trigger down to run as fast as it can.
2.Use the little screwdriver to turn the high-speed in and out until you find the spot where the string trimmer running the fastest.
3.Unscrew the high-speed screw slowly until you hear the RPM (revolution per minute) start to drop, then turn the screw back in again until you hear the RPM just come up to a position where it is making the humming sound.
That is the ideal position of the high-speed screw.

The Low-Speed Screw

1.Here, you do not need to hold on to the trigger, you just need to leave it at idle. If the string trimmer does not idle, you just need to turn the low-speed screw in until it idles.
2.Similar to the high-speed screw, turn the low-speed screw in and out until you find the sweet spot where the string trimmer idling the fastest.
3.Turn the low-speed screw out very slowly until you hear the RPM just start to drop.
4.Leave it there, do not turn it back in.
You will receive an excellent trigger reaction when you punch the trigger again.
By the way, you’d better check if the carb is leaking fuel especially when pressing the bulb, replace the carb if necessary. Check the fuel flow after you put on the new carb, then put all things back on and try to start it.

HIPA CARBURETOR  REPLACEMENT

Click here and BUY IT NOW: Hipa Carburetor Replacement

Please let us know if this works and if you have any suggestions or comments. Or you can join HIPA DIY COMMUNITY to feature your passion for repair projects, share your stories with the Hipa family and get help from Hipa.
Prev Post
Next Post

Leave a comment

Please note, comments need to be approved before they are published.

You May Also Like

Thanks for subscribing!

This email has been registered!

Shop the look

Choose Options

Hipa
Register to get FREE level-5 cut-resistant gloves(worth $9.9) now, FREE SHIPPING !!!

Recently Viewed

Close
Edit Option
Close
Have Questions?
Close
Sign Up To Get Free Gifts
this is just a warning
Login Close
Close
Shopping Cart
0 items